Ps3 controller laptop driver

Find the PlayStation 3 controller in the list and check it. Bluetooth installation note: Make sure the 'Install Bluetooth driver' box is checked.

Like you did with the Dualshock 3, click the arrow next to 'Choose Bluetooth dongles to install' and find your Bluetooth device in the list. Check it. Click Install. Watch the SCP Toolkit run through its installation process. You'll see lots of pop-ups on the side of your screen as it detects your hardware. Scroll to the bottom of the log and you should hopefully see 'Dualshock 3 USB Driver installed' and 'Bluetooth Driver installed' if you chose to , signifying a successful installation. If all went well, click Exit.

Now that it's installed, you'll see ScpToolkit as an icon in your system tray. Here you can change some settings like disabling rumble, adjusting analog stick deadzones, and more. Most of these settings you should be able to leave alone. ScpToolkit starts up with Windows by default, and also plays some sound effects that you might find obnoxious.

To disable them, click the Sound settings tab and uncheck 'Enable notification sounds. If you plan to use your PS3 controller with the emulator, click Browse to navigate to your PCSX2 installation folder, then click Enable to install the patch. Now that it's installed, the Dualshock 3 should behave like an Xbox controller. Any game with native XInput support—pretty much any modern PC game that supports gamepads—should recognize it without a hitch. Some games let you manually choose your button icons, though.

Look for that in game settings! If you ran into issues installing ScpToolkit or using the controller, you can try posting in the official thread at the PCSX2 forums , but you may not get an answer. If you're not about that wired business, and followed all the Bluetooth installation steps above, you should be able to simply unplug the controller, and after a couple seconds it will sync via Bluetooth. You'll get a notification in the system tray when it does.

This works after a reboot, too. If you allow ScpToolkit to start with Windows, you should simply be able to plug in your PS3 controller again and it'll instantly be recognized. Once the LED is on, unplug the controller, and it'll once again be synced via Bluetooth. To disable them, click the Sound settings tab and uncheck "Enable notification sounds. If you plan to use your PS3 controller with the emulator, click Browse to navigate to your PCSX2 installation folder, then click Enable to install the patch.

Now that it's installed, the Dualshock 3 should behave like an Xbox controller. Any game with native XInput support—pretty much any modern PC game that supports gamepads—should recognize it without a hitch.

Some games let you manually choose your button icons, though. Look for that in game settings! If you ran into issues installing ScpToolkit or using the controller, you can try posting in the official thread at the PCSX2 forums , but you may not get an answer. If you're not about that wired business, and followed all the Bluetooth installation steps above, you should be able to simply unplug the controller, and after a couple seconds it will sync via Bluetooth.

You'll get a notification in the system tray when it does. This works after a reboot, too. If you allow ScpToolkit to start with Windows, you should simply be able to plug in your PS3 controller again and it'll instantly be recognized. Once the LED is on, unplug the controller, and it'll once again be synced via Bluetooth. If you have issues with Bluetooth, it could be that your dongle isn't supported. You may also find help in ScpToolkit's Github discussions. Bluetooth can be finicky, and any problem you run into could be due to hardware, or your particular version of Windows, or drivers… in other words, good luck.

In this post, you can get 4 solution to it. Try them one by one until it is fixed. Step 1: Make sure you have a Bluetooth dongle plugged in or your motherboard's Bluetooth enabled. Step 2: You also need to install ScpToolkit. When you choose features to be installed, you should make sure the ScpToolkit Bluetooth Pair Utility option is ticked. Then, when installing drivers, you should make sure the " Install Bluetooth driver " box is checked, then click the arrow next to " Choose Bluetooth dongles to install " and find your Bluetooth device in the list to check it.

Step 3: If all went well, you should be able to simply unplug the controller, and after a couple seconds it will sync via Bluetooth. This post recommends 2 PS3 internal hard drives and 2 PS3 external hard drives to you. After you have installed required drivers, you will need an emulator which will recognize your PS3 controller as Xbox controller. We are using SCP toolkit as the emulator. Save my name, email, and website in this browser for the next time I comment. How to install the PS3 controller in Windows?